mainmenu_option next_comment
comment 'Block device drivers'

tristate 'Loopback device support' CONFIG_BLK_DEV_LOOP
dep_tristate 'Network block device support' CONFIG_BLK_DEV_NBD $CONFIG_NET
tristate 'RAM disk support' CONFIG_BLK_DEV_RAM
if [ "$CONFIG_BLK_DEV_RAM" = "y" -o "$CONFIG_BLK_DEV_RAM" = "m" ]; then
  int '   Default RAM disk size' CONFIG_BLK_DEV_RAM_SIZE 24576
fi
dep_bool '   Initial RAM disk (initrd) support' CONFIG_BLK_DEV_INITRD $CONFIG_BLK_DEV_RAM
tristate 'XPRAM disk support' CONFIG_BLK_DEV_XPRAM

comment 'S/390 block device drivers'

tristate 'Support for DASD devices' CONFIG_DASD
if [ "$CONFIG_DASD" != "n"  ]; then
  dep_tristate '   Support for ECKD Disks' CONFIG_DASD_ECKD $CONFIG_DASD
  if [ "$CONFIG_DASD_ECKD" = "m" ]; then
    bool     '   Automatic activation of ECKD module' CONFIG_DASD_AUTO_ECKD
  fi;
  dep_tristate '   Support for FBA  Disks' CONFIG_DASD_FBA $CONFIG_DASD
  if [ "$CONFIG_DASD_FBA" = "m" ]; then
    bool     '   Automatic activation of FBA  module' CONFIG_DASD_AUTO_FBA
  fi;
#  dep_tristate '   Support for CKD  Disks' CONFIG_DASD_CKD $CONFIG_DASD
  if [ "$CONFIG_ARCH_S390X" != "y" ]; then
    dep_tristate '   Support for DIAG access to CMS reserved Disks' CONFIG_DASD_DIAG $CONFIG_DASD
    if [ "$CONFIG_DASD_DIAG" = "m" ]; then
      bool     '   Automatic activation of DIAG module' CONFIG_DASD_AUTO_DIAG
    fi;
  fi; 
fi

endmenu

source drivers/md/Config.in

mainmenu_option next_comment
comment 'Character device drivers'
bool 'Unix98 PTY support' CONFIG_UNIX98_PTYS
if [ "$CONFIG_UNIX98_PTYS" = "y" ]; then
  int 'Maximum number of Unix98 PTYs in use (0-2048)' CONFIG_UNIX98_PTY_COUNT 256
fi

comment 'S/390 character device drivers'

tristate 'Support for locally attached 3270 tubes' CONFIG_TN3270
if [ "$CONFIG_TN3270" = "y" ]; then
  bool 'Support for console on 3270 line mode terminal' CONFIG_TN3270_CONSOLE
fi
bool 'Support for 3215 line mode terminal' CONFIG_TN3215
if [ "$CONFIG_TN3215" = "y" ]; then
  bool 'Support for console on 3215 line mode terminal' CONFIG_TN3215_CONSOLE
fi
bool 'Support for HWC line mode terminal' CONFIG_HWC
if [ "$CONFIG_HWC" = "y" ]; then
  bool '   console on HWC line mode terminal' CONFIG_HWC_CONSOLE
  tristate '   Control-Program Identification' CONFIG_HWC_CPI
fi
tristate 'S/390 tape device support' CONFIG_S390_TAPE
if [ "$CONFIG_S390_TAPE" != "n" ]; then
  comment 'S/390 tape interface support'
  bool '   Support for tape character devices' CONFIG_S390_TAPE_CHAR
  bool '   Support for tape block devices' CONFIG_S390_TAPE_BLOCK
  comment 'S/390 tape hardware support'
  bool '   Support for 3490 tape hardware' CONFIG_S390_TAPE_3490
  bool '   Support for 3480 tape hardware' CONFIG_S390_TAPE_3480
fi
endmenu

if [ "$CONFIG_NET" = "y" ]; then
  mainmenu_option next_comment
  comment 'Network device drivers'
  bool 'Network device support' CONFIG_NETDEVICES

  if [ "$CONFIG_NETDEVICES" = "y" ]; then
    tristate 'Dummy net driver support' CONFIG_DUMMY
    tristate 'Bonding driver support' CONFIG_BONDING
    tristate 'EQL (serial line load balancing) support' CONFIG_EQUALIZER
    tristate 'Universal TUN/TAP device driver support' CONFIG_TUN
    bool 'Ethernet (10 or 100Mbit)' CONFIG_NET_ETHERNET
    bool 'Token Ring driver support' CONFIG_TR
    bool 'FDDI driver support' CONFIG_FDDI
    comment 'S/390 network device drivers'
    bool 'Channel Device Configuration' CONFIG_CHANDEV
    if [ "$CONFIG_CHANDEV" = "y" ]; then
	define_bool CONFIG_HOTPLUG y
    fi

    tristate 'CTC device support' CONFIG_CTC
    tristate 'IUCV device support (VM only)' CONFIG_IUCV
  fi
  endmenu
fi